Product Description
Auto Red Brick Stacking Machine Multifunctional Hollow Block Equipment 22.5kw
Production introduce
The automatic hydralic brick setting machine (ZMP) is mainly used in tunnel kiln’s once brick stacking and firing and hoffman kiln’s twice brick stacking and firing,automatic contral and hydralic lifting with the feartures of energy-efficient,simple maintenance,low cost,stable and smooth operation.
The automatic hydralic brick setting machine is formed by walking car,chuck,separating machine ,lifting guide pillar,rail,hydralic system and electrica system,etc.
Production parts
The full-automatic brick setting machine is formed by moving trestle , clamp plate , separator , lifting guide pillar , rail , hydraulic system and electrical system , etc.
Operating principle
The operating principle of automatic hydralic brick setting machine:the cutting machine will push the wet bricks onto the storage transition table.when the pieces of wet bricks on the storage transition table reaches a number,the cutting machine will push the wet beicks again onto the intelligent separater table.The lifting cylinder will move down when the wet bricks are devided into strips on the separator table by the separatingsystem.Then the chuck will pick up the wet bricks by the driving of lifting cylinder to a predetermined height.During the lifting period,the separating system will adjustt the stacking channel and brick brick space based on the kiln firing desigh.The wet bricks will be stacked onto the trolley car if the chuck opening the manganese plate by the cylinder.The brick setting machine can finish the brick stacking working through the cycle of all complete process as above.All this functions are centralized control by electric,the operator just need to start the appropriate procedures,the brick setting machine can achieve the operating automatically.
Characteristics
1. The brick machine setting machine is automatic working, reduce the use of manpower, high efficiency, and large capacity
2. ZMP series Automatic Setting Machine are applied to the first time sinter and the second sinter.
3. And this can pick up the grouped billet automatic calmly (wet billet and dry billet) and then put down them to the assigned position in the billet lay car.
4. There are many ways to putting down the billet, such as putting down billet in face up or putting down
billet in side face.
5. Toward to the different shape of kiln ways to putting down the billet, such as putting down billet in face up or putting down billet in side face.
6. Toward to the different shape of kiln and different output, there are different automatic setting machines
Production site
The workflow of hydraullic brick setting machine:when the cutter pushes the green bricks to the separating board , the separator starts work , it drives the separating board stretch and separate the bricks . When the brick separating is finished , the lift cylinder turns down .When the clamp plate reaches the pre-set location , the clamp plate fixture picks up the bricks ,and then it is lifted to a predetermined height by the lifting cylinder . After all those progress , the separator opens the air duct and the moving evice drives brick stacking machine to the top of the kiln car , the kiln car rotates 90° and then lift cylinder drops down to a predetermined height for setting bricks , the clamp plate opens and lays the bricks on the kiln car , it completes stacking stacking process automatically . With the periodical operation the whole stacking work is finished , all the functiongs are centralized controlled automatically.
Technical Parameters
|
data
modle
|
Load weight(t) |
Setting capacity(piece/time) |
Working frequency(s/time) |
Production capacity(piece/h) |
Highly(m) |
Applicable type kiln |
| ZMP300 |
1 |
240 |
40 |
15000 |
0-1.725 |
Hoffman kiln or 3 meters cross section of tunnel kiln
|
| ZMP360 |
2.2 |
380 |
60 |
22800 |
0-1.725 |
3.6 meters cross section of tunnel kiln
|
| ZMP460 |
3.8 |
600 |
60 |
36000 |
0-1.725 |
4.6 meters cross section of tunnel kiln
|
Service policy
►Before sales
1. cept customer consultation, according to the customer demand; determine the scale of factory management, providing solutions.
2. r customer training and technical personnel
3. cording to customer request, design and manufacture products
4. company sent engineering and technical personnel to the user scene, planning for the optimal design of the flow field, and the solutions.
5. customers in relevant technical documents.
►Medium-sales
1. ceptance of the product
2. sist client protocol construction scheme
►After-sales
1. aining personnel
2. point special after-sale service staff, arrived at the scene guide clients installation and commissioning.
3. gular visit customer, consult with the customer feedback, come true with the customer's two-way communication
Customer visit
Welcome to us,we have professional team.We can shoew you our workshop to kown us more.
About us
Established in 1976s ,Wangda machinery has developed into a famous manufacturer through 40 years struggling and progressing, specialized in producing vacuum extruder, clay brick making machine, hollow brick making machine,Fired brick, Solid clay brick making machine.
Your message must be between 20-3,000 characters!